Alloy 400
Alloy 400 commonly known as MONEL® 400, is a nickel–copper solid‑solution alloy offering high strength, excellent toughness, and exceptional resistance to many corrosive environments. It performs reliably across a wide temperature range and is especially valued in marine, chemical, and hydrocarbon processing applications.
Standards & Designations
- UNS: N04400
- EN / W. Nr.: 2.4360 / 2.4361
- ASTM/ASME: B127 (plate/sheet/strip), B163 & B165 (pipe/tube), B164 (bar), B564 (forgings)
Corrosion resistance
Alloy 400 provides strong corrosion immunity across a broad spectrum of service environments. It is highly resistant to seawater, steam, and brackish water, including rapidly flowing warm seawater. It performs well in non‑oxidizing mineral acids, alkaline solutions, and chloride environments, and shows notable resistance to hydrochloric and hydrofluoric acids when de‑aerated.
Heat treatment
Alloy 400 cannot be strengthened by heat treatment and is hardened only through cold work, as it is a solid‑solution nickel–copper alloy.
Its primary thermal treatment is annealing, which is used to restore ductility after cold work.
Welding
- Machining: Because Alloy 400 work‑hardens rapidly, machining requires rigid tooling, heavy feeds, and sharp cutting edges. Its behavior is similar to that of other high‑nickel alloys. The more machinable alternative, Alloy R405, is sometimes chosen when extensive machining is required.
- Forming: Alloy 400 is highly ductile and can be readily formed using standard cold‑ and hot‑working operations. As a solid-solution alloy, it hardens only by cold work, which can be used strategically to increase strength.
It offers good workability across plate, sheet, strip, and long products, and is supplied in tempers that allow adjustments to required strength levels.
- Welding: Alloy 400 exhibits good weldability, making it suitable for fabrication using most conventional welding processes.
Welds maintain strong resistance to general corrosion and are fully compatible with the alloy’s performance in marine and chemical environments. When welding is performed correctly, Alloy 400 remains resistant to chloride stress‑corrosion cracking and maintains its mechanical strength.
Typical applications
The list of applications for this general purpose grade is very extensive and includes:
- pumps, valves, and propeller shafts
- heat‑exchanger
- marine fixtures
- seawater equipment
- refinery transfer piping
- distillation towers
- steam generator tubing
- petroleum stills
- chemical processing equipment
Chemical Composition (%)
| Grade | Ni-Co | Cu | Fe | Mn | Si | C | S |
|---|---|---|---|---|---|---|---|
| 400 | 63.0-70.0 | 28.0–34.0 | 2.5 max | 2.0 max | 0.5 max | 0.3 max | .024 max |
Mechanical properties (annealed)
| Yield Strength .2% Offset (psi) | Ultimate Strength (psi) | Elongation in 2” (%) | Hardness (Rb) |
|---|---|---|---|
| 25,000 – 55,000 | 70,000 – 90,000 | 35-60 | 85 |
Other properties
| Specific Heat (BTU/lb-°F) | Electrical Resistivity at 68⁰F (μΩ-cm) | Poisson’s Ratio | Specific Gravity | Thermal Expansion 70⁰ – 200⁰F (In/In/⁰F×10‾⁶) | Thermal Conductivity (BTU./ft.₂/hr./⁰F/ft) |
|---|---|---|---|---|---|
| 0.10 | 51 | 0.32 | 8.83 | 7.7 × 10⁻⁶ /K | 14.0 (at 200⁰F) |
